Stenkross

[rainman1618]

Här kommer några bilder på min elektriska 220 volts stenkross.
//borax

kul att se att motorn funka.

[borax]

Funkar klockrent.

[borax]

Jag tror att du har kopplat den fel när du kopplade in sladden.

[Aquatek69]

No, everything runs great with no crusher connected, really smooth, when I connect it, it starts to move but the breaker in my house trips....

[iller]

Vi vill ha en film också

[borax]

Jag tror att du har kopplat den fel när du kopplade in sladden.

Jag tror att du har kopplat den fel när du kopplade in sladden.

No, everything runs great with no crusher connected, really smooth, when I connect it, it starts to move but the breaker in my house trips....

Okej min motor kunde jag koppla på flera vis den gick att koppla som 1 fas och 2 fas och i USA har dom 2 faser ibland på svetsmaskiner jag bara tänkte så det inte var det felet.

[borax]

Vi vill ha en film också

Jag ska se om jag får till en liten film med mobilen som jag kan lägga upp här inte min starka sida det där med film.

[borax]

Lägger upp en film med Cobra Crusher som man kan använda en vinkelslip å driva den med.

Och här tror jag man kan beställa en om man blir sugen. http://cobracrusher.com/prelaunch/

[borax]

No, everything runs great with no crusher connected, really smooth, when I connect it, it starts to move but the breaker in my house trips....

Hej pratade med mi Son som är elektriker idag om din kross. Han undrade om du har provat flera väggutag så att det inte är fasen i väggutaget som är belastat med någpot annat kanske en frys eller spis eller nåt sånt så du inte får full effekt ur det.

[Aquatek69]

That was exactly what I was thinking earlier today, the connection I was using is at the opposite end of the house from the fuze box & there are other things connected to that line..... I will take it down to my parking area & try the outside connector there as the fuze box is very close, i use a biltema svets machine from this socket with no problem so I hope it works....
Thanks for the help.

These crushers are HEAVY!!!

[borax]

Vi hoppas att det är felet.

[Aquatek69]

Here's the problem, the little Chinese men who made my motor were having an April fool joke! It ran this morning (disconnected from the crusher) for 30 seconds & it tripped the breaker in the house again, I turned the shaft & there were very tight spots. I thought it was a bearing so I slackened the main bolts that hold it together & took the back off.
There was a disconnected wire that should be soldered to the back plate so I re-soldered it back in place. I connected everything back together but it is impossible to tighten the bolts without the shaft having very tight spots so I got it to the best "free turning" position that I could.
I plugged it in & "pop" a spark came out of the back & tripped the main 25 amp breaker which turned everything off in my house.
Sometimes the Chinese junk works but i'm done with this piece of shit before it burns my house down or kills me........ I'll maybe hook an engine to the crusher (not Chinese)....

[borax]

Here's the problem, the little Chinese men who made my motor were having an April fool joke! It ran this morning (disconnected from the crusher) for 30 seconds & it tripped the breaker in the house again, I turned the shaft & there were very tight spots. I thought it was a bearing so I slackened the main bolts that hold it together & took the back off.
There was a disconnected wire that should be soldered to the back plate so I re-soldered it back in place. I connected everything back together but it is impossible to tighten the bolts without the shaft having very tight spots so I got it to the best "free turning" position that I could.
I plugged it in & "pop" a spark came out of the back & tripped the main 25 amp breaker which turned everything off in my house.
Sometimes the Chinese junk works but i'm done with this piece of shit before it burns my house down or kills me........ I'll maybe hook an engine to the crusher (not Chinese)....

Jag är ledsen att din motor inte fungerade men du kan använda en 1fas 1500RPM motor och det fungerar alldeles utmärkt